Free Download Audi J518 EEPROM Converter

 There are some dumps which has 2k and need to be converted to 4kb file for the eeprom of new emulators or new j518 boards

Here is the simple tool which allows you to transfer 2kb eeprom data from 3l40k for example to 0l01y. For j518 (also j518 elv emulators)

 

Credit to Josef from MHHAUTO.

 

 

Previous version DumpConverter

File including

Also a 32bit version

Here is the new version J518 Eeprom Converter V1.1 (Dec. 2022)

https://mega.nz/file/zyxmCS7Y#lSgop6H8LTMRZizJJuqq_FPP53T3vXvCw2ujqHA3Xkg

New update:

other way around also available now

File including

NOTE:

Yes it’s based on .net core. If failed to run this converter, install Windows Desktop Runtime program. Win7 is ok.

 

 

How to Write Audi J518 256, 128 ELV Emulator with Xhorse VVDI Prog?

 

9S12DG 128 CPU operation steps:

 

• Read and backup original EEPROM data.

Do backup original eeprom data in case of lose data before operation. Read and save data.

The original car data can be restored after an operation error, just in case.

 

• Paste EEPROM data to EEPROM 2K-4K folder.

Run EEPROM Converter. Convert original 2kb file to 4kb.

 

• 3.Write the converted 4k eeprom file.

 

For simulator is chip 256, select J518(2010)(0L01Y)

Connect flashing wire and write the converted EEPROM file.

Attention: simulator is a 256 chip then choose  J518 (2010) (0L01Y) option.

Each ELV emulator board contains both eeprom data and FLSAH data, so usually you just need to write Eeprom data. If not, you can write original eeprom data and the FLASH data in the emulator.

 

If car ELV has 9S12DG 256 CPU, the operation steps are as follows.

Read out and save the original eeprom data, and write it directly to the simulator.

without horn wiring connection

red (thick) =VCC

black (thick) =GND

yellow =RST

purple =BKGD

green =XCLKS

White =CLK

black (fine) =GND-C

with horn wiring connection

follow same wiring diagram as without horn above

With the VVDI Prog Dedicated Programming Cable, you can connect ELV emulator without soldering, directly insert into the 20pin port.

Attention:

Better put J518 ELV emulator to car after write data.

In the test platform test, better check the wiring of 20Pin port. Some test platforms will conflict with the 20pin port which leads to the chip being corrupted.

 

Error wiring: 10 (red) should be in position 20 (blue), as shown in the figure

How to Change the Audi J518 ELV Emulator?

 Problem:

Could you help program this type of J518 ELV emulator? Already read EEPROM and flash from original ELV. Write eeprom with 4kb size. But car don’t start. Even recognize key.

 

Solution:

The ELV Emulator is used to replace the Audi C6 A6 Q7 steering column module J518 module when it’s failure.

The Audi sixth generation Immo A6 Q7 car usually seen faults like, turn on the key car not start, ELV not unlock, cluster not light up etc, most of the time it can be repaired by the J518 ELV module by changing the original J518 ELV Module with this J518 emulator. 

How to Change the Audi J518 ELV Emulator?

1.Read out the EEPROM data from the original J518 module of your car (the emulator was already with flash data)
2. Write the EEPROM data you got in Step 1 into the emulator (if the original J518 MCU mask is 0L01Y, write the EEPROM data you got from step1 into the emulator directly;
or if the MCU mask of the original J518 is 1L59W/3L40K, you need to send EEPROM data to an expert to transfer EEPROM data when you write into the emulator directly. We don’t provide the service)

Feature:
It’s a universal solution, compatible with the three MCU types (1L59W, 3L40K, 0L01Y) of the original J518 module utilized.
Remove the vulnerable components, works more stable and durable.
With a simulated lock and unlock sounds generated by the horn on the board.
Easy for replacing.

 

Note:
The VVDIProg cable connector here is only for write the data to this emulator, not able to read the original J518 module
For reading the original J518 module data, still have to use the programmer solder wire to read.
This emulator has no lock and unlock function, if you need the module function as the original one on the ar, select the J518 replacement PCB.

www.obdii365.com