How to Install ODIS-S 24.1.2 for VNCI 6154A?

 Here we will how to install and configure the newest VAG ODIS Service 24.1.2 software with VNCI 6154A red interface.

 

 

ODIS Service (ODIS-S) 24.1.2, PostSetup 240102.101.10

Compatible devices: VAS6154 genuine devices or with passthru interfaces VNCI 6154A red interface etc.

VXDIAG driver is not ready for this version.

Operating system: Windows 10, Windows 11

How to Install ODIS-S 24.1.2 for VNCI 6154A?

NOTE:
There are different versions of ODIS Servicer 24. Here is the installation instructions for our ODIS 24.1.2 software. Search our blog or contact us for software if you need.

Software contains these files.

Extarct ODIS-S_PostSetup_24.1.2.zip folder

Run ODIS-S_24.1.2.exe setup
Select setup language

Select Diagnostic Interface as VAS 6154A and continue

If it asks to search the license, press Next.

Finish installing setup.

Run patch folder
Copy OffboardDiagLaunncher.exe and license.dat files and paste to the C:/Program Files/OS folder.

Run OffboardDiagLaunncher.exe from C:/Program Files/OS folder as administrator

Select local directory
Select ODIS-S PostSetup_24.1.2 folder

Select PostSetup language.

Installing postsetup database.
Finish installing postsetup database.

Run ODIS-S 24 software on the desktop.
Go to Admin, set for connection types to Internet.

Select VCI type as VAS 6154A.

Now software is ready to

http://blog.obdii365.com/2024/12/23/how-to-install-and-configure-odis-s-24-1-2-for-vnci-6154a/

Xhorse Multi Prog Clone VW Bentley Siemens VDO KESSY Module

 This is an old Bentley, a flood car. Here we will show how to get this immobilizer clone so that we can finally start it up.

The KESSY Module out of a Bentley. The drowned one needs to be cloned. The cloning is for KESSY.

We have the original drowned one and another KESSY module from junkyard.

Here shows how to clone the KESSY module using Xhorse Multi Prog programmer.

Run Multiprog software, select VW-KESSY Backup read & write (2008-) (WLED)

Check wiring diagram.

Make a strong zoom-in, every point must be welded on it.

Make sure everything is connected to the wiring diagram.

Read eeprom data.
Verify data.
and save original KESSY eeprom file.

Disconnect wires on the original KESSY module.

This is a donor KESSY module.
Connect junkyard KESSY module with xhorse multi prog and mcu adapter following the same wiring diagrm.

Backup the eeprom of the donor KESSY module.

Open original KESSY data and write to the junkyard module.

Write original backup data successfully.

Read KESSY module data again.

Make a comparison between the new KESSY data and original KESSY data.

The two files being compared are the same.

So the KESSY module is cloned by xhorse multi prog successfully.

http://blog.obdii365.com/2024/12/23/clone-vw-bentley-siemens-vdo-kessy-by-xhorse-multi-prog/

How to Use Xhorse MLB Tool Solder Free Adapters?

 Xhorse released a new MLB solder free adapter kit to work with VVDI MLB Tool for VW, Audi, Lamborghini, Bentley and Porsche MLB key programming.  No need to solder, just use a plier to remove 2 capacitors.

Obdii365.com here shows how to use/connect the MLB solder free adapters.

Step 1: Remove capacitors on original key.

Connect VVDI MLB Tool with key tool plus via OTG converter.

Go to Immo programming->Audi->Select by type->MLB immobilizer systems.

Select the corresponding key type and check wiring diagram.

Remove components (2 capacitors) of original key as the diagram shown.
 

2. Connect MLB solder free adapter with original MLB key board

Make sure the pins on the adapter match the contacts marked on the diagram.

Fasten the buckle.
The short side of the buckle faces upwards, and the long side marked in white faces downwards.

3. Connect MLB adapter with MLB tool
After connecting Xhorse MLB adapter with key,  connect the MLB adapter with the MLB tool.
Pay attention to the orientation of the adapter so that it ends up in the sensing area.

Step 4: Now you can add a spare MLB key.

Check the key programming guide here (ignore the soldering part).

How to Add VAG MLB Key with VVDI MLB Tool and VVDI Key Tool Plus?

How to Update Yanhua ACDP2 PCF-Key Adapter Firmware?

 Problem:

Making dealer key for VW with Yanhua ACDP2 module 33 on bench and it says this when i put key into pcf key adapter.

Error “PCF-Key Adapter version is low”.

Where I have to update the adapter firmware?

Solution:

Go to Special Function.

Hit Adapter Upgrade.

Select PCF-KEY Upgrade.

Connect PCF-KEY Adapter with ACDP2 and update adapter firmware.

http://blog.obdii365.com/2024/12/18/yanhua-acdp2-pcf-key-adapter-version-is-low-solution/

Search PSA EDC17C60 PIN Code from EEPROM Dump

 Question:

Is it possible to read PIN code from PSA EDC17C60 ECU eeprom dump read by Foxflash or CG FC200 etc?

It is a 2018 Peugeot Partner with 1.6HDi EDC17c60. Need to get PIN code to make spare key.

Here is the clue.

Yes, it is possible.

This is the method.

In PSA EDC17C60 EEPROM is the PIN code located around the offset 3700.
It is a 4 alfa-numeric code that you will find twice in that area (eg. @ 3780 and @3800).

EEPROM PIN CODE

Click to enlarge image.

 

FYI:

OBDSTAR DC706 now will read and write EDC17C60, also read pin and make TPROT OFF directly in the machine.

https://youtu.be/kyVSTQfbAE4

Tops to Bypass Renault Zoe 2022 Security Gateway

 Is there any chance to bypass the Renault Zoe facelift 2020 Security Gateway? A Renault electrical model. It looks identical to Trafic 3.

This 40pin Nissan cable from Lonsdor working fine for gateway bypass.

You must use the grey cable from the BCM.

The emergency coil NOT IN THE START BUTTON put the card front of the gear selector.

 

How to connect the BCM 40 Pin cable to BCM?

That cable is like an extension cord.
Pull out the grey cable from the BCM.
Put the grey cable into the BCM40 cable socket.
and put back the 40pin cable plug into the BCM now empty socket (where from you pulled out the grey cable).
The BCM obd plug into the car’s obd socket and you have an empty obd socket with 12V (from the obd port and the can lines from the BCM thru the extension cord)
No need to cut or pining damaging anything.
plain and simple.

Lonsdor K518 Pro, OBDSTAR X300 DP Plus/G3 and Autel IM508/IM608 will program a new card without PINCODE (Free pincode).

Autel is not really straightforward.  DO NOT leave the learning process before it’s finished because there will be no ignition at the end.

Always keep good battery and battery maintainer when doing these Renault new smart keys.