Autel With Integrated AllData OEM Repair Data

Starting in November, Autel and ALLDATA are bringing factory repair information directly into your diagnostic workflow through an industry-first integration on supported MaxiSYS tablets.

With an active Autel software subscription and ALLDATA subscription, technicians can move seamlessly from fault codes to vehicle-specific OEM repair procedures, wiring diagrams, and diagnostic information—all on one screen, right at the vehicle—helping streamline troubleshooting and accelerate repairs.

Supported models include the

• MaxiSYS Ultra S2,
• MS919 S2,
• MS909 S2,
• MaxiSYS Ultra,
• MS919,
• MS909,
• Ultra ADAS,
• Ultra EV.

Limited Time Offer: Save 15% on ALLDATA
Use promo code AUTEL15 during checkout. New customers only.
Excludes National Accounts. Offer valid November 1–21, 2026.
*Active Autel software subscription and separate ALLDATA subscription required for integration.

 

Eoneboss Adds Toyota 4A B6 Smart Remote Generation

Great news for automotive locksmiths and car key professionals! EoneBoss App update Toyota 4A-B6 remote generation function.

 

EoneBoss has expanded its Toyota 4A key generation compatibility. In addition to the previously supported 4A-AA and 4A-BA, 4A-B6 is now supported!

No New Original Keys, No Additional Devices, More Compatibility, More Possibilities!

Compatible Key Models (All Bluetooth Versions):
· ET-14 (4B)
· ET-14 (5B)
· ET-15

Expanded 4A Compatibility:
All the above models now support:
4A-AA
4A-BA
4A-B6 (NEW)

Supported Vehicles:
Toyota Camry, Avalon, and more.

Supported Board Number: 0110, 2561.

 

APP UPDATE ALERT!
EoneBoss mobile App has been updated! You can now check the detailed information and supported list directly on the App right now.

Update yours and explore today!

 

What Tool to Program Fiat Ducato 4A All Keys Lost?

What device to program 2022-2025 Fiat Ducato equipped with a Hightech AES ID4A transponder all keys lost?
Add key and AKL is possible via OBD port with FCA Stellantis and precoded dealer key.
With aftermarket tools the key learning is done first via bench reading.

Autel IM608/Xhorse won’t do it at the moment.
Pull out the BCM, read data with OBDSTAR G3+ MP001+ C4-09 adapter on bench mode.

Retrieve the PIN code with BCM dump.

OBDSTAR G3 will also program key. G3 can do the job but remote will not work as the precoding function doesn’t work correctly, only trasponder work, you can transfer data to avdi or zedfull to pre code correctly then learn keys in.

Note: Not all aftermarket programmers support correct key pre-coding, which will cause the remote control functions to remain inoperative after programming. For successful key pre-coding, use Abrites AVDI/Zedfull, which has been tested and verified by many.

Read the flash and EEPROM using Obdstar, apply the precoding with Abrites, and then write the data back; you need to perform this by connecting to the CAN bus from the right-hand side.

 

 

 

 

Flex Hyundai SIM2K-510 SGW Detected Error Solution

Problem:

Tried to read the 2024 Hyundai Sportage Kefico SIM2K-510 ECU using Flex programmer by OBD.

Flex software says SGW detected and failed to connect via OBD.
No communication on bench (ERROR).

Any solution?

Solution:

This model uses CAN FD communication and Flex detects SGW gateway. You must connect a CAN FD adapter (FLX4.4) for reading.

The FLX4.4 adapter is on preorder now and will be shipped from 19th November, 2026.

Flex FLX4.4 CAN FD Adapter pinout

Is a CAN FD adapter necessary for this protocol?
Only for vehicles equipped with protected gateway (SGW).

 

FYI:
You can read ecu on bench by obd protocol but for this need FL4.4 adapter.