2022/11/29

Visteon DCU102 DCU104 Pinout to Ktag KT200

 There are many ecu programmers that can be used to read and write Visteon dcu102 dcu104 in Ford and PSA group, including KT200, Foxflash, Ktag, Dimsport, Autotuner etc.

Check pinout wiring diagram to each device respectively.

 

1.Visteon DCU 102 DCU104 pinout to Ktag

Ktag 7.020 tested and working.

Visteon DCU 102 pinout to Ktag

Ktag Vistion DCU 102 pinout
Visteon DCU104 pinout to Ktag

Ktag Vistion DCU 104 pinout
Example: Ford DCU104 work done with ktag clone
Read with KTAG in boot mode. ksuite SW correct automatically checksum on Flash/micro/maps etc.
Visteon DCU 102 DCU104 ktag 1

Visteon DCU 102 DCU104 ktag 2

Visteon DCU 102 DCU104 ktag 3

Visteon DCU 102 DCU104 ktag 4

NOTE: Ford DCU can be read and written by obd kess, PSA can be just written obd.

2.Visteon DCU 102 DCU104 pinout to KT200/FoxFlash/DFox

 

VISTEON Fomoco DCU-10x [ST10F276] – Fiat,Ford,Peugeot,Citroen [Gasoline]

Connect multifunction cable and the resistances as shown.

Visteon DCU 102 DCU104 ktag 5

Visteon DCU 102 DCU104 ktag 6

To read and write use the following driver:
→ TOOLS BOOT MODE
→ ST ST10Fxxx
→ ST10F273 / ST10F275 / ST10F276 *K
or
→ ST10F273 / ST10F275 / ST10F276 *CAN

 

Alternatively, read via RX TX:

Kit to use:
– Multifunction cable
– 2 resistance of 1000 Ω
– Transistor PNP 2N3906

Connect multifunction cable and the resistances as shown.

Visteon DCU 102 DCU104 ktag 7

Visteon DCU 102 DCU104 ktag 8

To read and write use the following driver:
→ TOOLS BOOT MODE
→ ST ST10Fxxx
→ ST10F273 / ST10F275 / ST10F276 *RxTx

 

VISTEON DCU-104 [ST10F276] – Fiat,Ford,Peugeot,Citroen [Gasoline]

Connect multifunction cable and the resistance as shown.

 

Visteon DCU104 kt200 1

Visteon DCU104 kt200 2

To read and write use the following driver:
→ TOOLS BOOT MODE
→ ST ST10Fxxx
→ ST10F273 / ST10F275 / ST10F276 *CAN
or
→ ST10F273 / ST10F275 / ST10F276 *K

 

For example:

Citroen Jumper 2.2 HDI year 2010 Visteon DCU-102 KT200 working over boot mode. see 2 unsoldered pins like ktag’s. CNF is located at the side of your bench cable on/off switch.

Read only in Boot mode. I also tried obd writing Visteon DCU102. Perfect!

Visteon DCU102 kt200 1

Visteon DCU102 kt200 2

Visteon DCU102 kt200 3

Visteon DCU102 kt200 4

Visteon DCU 10X pinout to Dimsport 

Visteon DCU 10X pinout to dim sport

Visteon DCU 10X pinout to Fgtech

you can read & write with bootmode only
Tested to fgtech clone working great

Visteon DCU 10X pinout to Fgtech

Flex read it safe and fast in boot.

Autotuner can do all fast via Obd.

No comments:

Post a Comment